Welcome to LATNET store!

High-end geospatial solutions and equipment.

Book live Demo now.

New guide: machine control savings, in 3D

See what overcuts, extra passes and survey stakes really cost, and what CHCNAV dozer, grader and excavator systems save. Includes EasyNAV for farms.

Authorized CHCNAV dealer in Canada

3D Machine Control for Excavators, Dozers & Graders

CHCNAV 3D guidance and automatic control systems that put your design in the cab – dig and grade to plan with fewer stakes, fewer grade checks and less rework. Supplied, installed and supported from Calgary.

5machine control systems
±2 cmgrading accuracy (TG63)
< 2 hinstallation (EMG100)
100 HzIMU sensor (TD63 Pro)

Find your machine control system

Which machine?

What do you need on the excavator?

Showing 5 of 5 · tick Compare on up to 3 products to see them side by side

Recommended
Excavator
Excavator fitted with the CHCNAV TX73 3D guidance system: dual GNSS antennas and IMU sensors

Excavator system

CHCNAV TX73

Heavy-duty 3D excavator system

ExcavatorMachine
±0.1° sensorsAccuracy
3DControl

Demanding sites and heavy-duty machines

Recommended
ExcavatorGuidance
Excavator ready for the CHCNAV EasyNAV EMG100 2.5D guidance system

Excavator guidance

CHCNAV EasyNAV EMG100

Entry-level 2.5D excavator guidance

ExcavatorMachine
±3 cmAccuracy
GuidanceControl

Contractors moving from lasers and stakes

Recommended
GraderAutomaticDual GNSS
Motor grader for the CHCNAV TG63 3D automatic grade control system

Grader control

CHCNAV TG63

3D automatic grader control

Motor graderMachine
±2 cmAccuracy
AutomaticControl

Roads, pads and fine grading

Recommended
DozerAutomaticDual GNSS
Dozer with dual GNSS antennas on the blade for CHCNAV TD63 Pro automatic control

Dozer control

CHCNAV TD63 Pro

3D automatic dozer control

DozerMachine
±2 cmAccuracy
AutomaticControl

Bulk earthmoving and fine grading

Recommended
ExcavatorGuidanceDual GNSS
Excavator for the CHCNAV TX63 3D excavator guidance system

Excavator guidance

CHCNAV TX63

3D excavator guidance, previous model

ExcavatorMachine
±3 cmAccuracy
GuidanceControl

Earthmoving, trenching and site preparation

0 selected

How it works

How 3D machine control works

Machine control puts the design on the operator’s screen and the machine’s position on the design – so the crew digs and grades to the right level without stakes or constant grade checks. Click a step or a number on the diagram.

Design grade RTK base / network IN-CAB CUT 0.42 m CUT 0.08 m ON GRADE 1234

Savings estimator

What could machine control save you?

Move the three sliders to match your crew – the savings update instantly.

$200$3,000
½ day5 days
8 weeks52 weeks

We assume machine control cuts staking and grade-checking work by about half – a typical result on earthworks sites. Savings on fill and aggregate come on top.

Estimated savings per season

$0
$0spent on staking and checks today
0 dayscrew days freed up

= today. Machine control saves about half.

An estimate to support your decision, not a quote or guarantee. Want a figure for your fleet? We can work it out with you.

Discuss your project

Systems by machine

Guidance or automatic control?

Guidance shows the operator cut and fill to grade; automatic control also drives the hydraulics. Pick the machine to see the options.

3D guidance for excavators

The operator sees the bucket position against the design in 3D – for trenches, slopes, foundations and detailed digging without a grade checker.

  • Dig to grade first time
  • Fewer stakes and grade checks
  • Safer – less crew around the machine

Automatic blade control

Dual GNSS, IMU sensors and intelligent hydraulics hold the blade on the design surface automatically – reaching finished grade faster with less material.

  • Finished grade in fewer passes
  • Less material overrun
  • Consistent results for every operator

Base station or network

Machine control needs RTK corrections: run your own UHF base on site or connect over NTRIP to an RTK network such as LATNET’s CORS network in Alberta. Check grade with a CHCNAV rover.

  • UHF base for remote sites
  • NTRIP network where there is coverage
  • Same corrections for rovers and machines

Machine control from an authorized CHCNAV dealer

LATNET Technologies Ltd. supplies CHCNAV 3D machine control across Canada – excavator guidance, automatic dozer and grader control – with installation help, design file preparation support, training and local service from Calgary.

Complete your site with an iBase UHF base or the LATNET RTK network, check grade with a CHCNAV GNSS rover, and capture as-builts with LiDAR.

Machine Control FAQ

What is the difference between guidance and automatic control?
Guidance shows the operator where the bucket or blade is against the design, with cut and fill on screen. Automatic control, as on the TD63 Pro dozer and TG63 grader systems, also drives the hydraulics to hold the blade on grade.
How accurate is 3D machine control?
CHCNAV systems work at centimetre level – for example ±2 cm on the TG63 grader system and ±3 cm on the TX63 excavator system – depending on corrections, calibration and site conditions.
Do I need a base station?
You need RTK corrections. Use your own UHF base station such as the iBase, or connect over NTRIP to an RTK network such as the LATNET network in Alberta.
How long does installation take?
The EasyNAV EMG100 can be installed and calibrated in under 2 hours with standard tools. Ask us about installation for the TX, TD and TG systems on your machines.
Do you offer demos, installation and training?
Yes. Contact us to book a demo, and we help with setup and one-on-one training in Calgary or online.